Skip to content
HeaterSphereWarm homes · Lower bills
Heated Blankets & Pads

How to Troubleshoot Your Berkshire EZ Touch Heated Throw Blanket

Updated 8 min read
The short fix
To troubleshoot your Berkshire EZ Touch heated throw blanket, check the controller settings and ensure the blanket is laid flat. If problems persist, you may need to replace it.

Heated throw blankets like the Berkshire EZ Touch offer comfort during chilly evenings, but they can sometimes present issues. Understanding common problems and their solutions can help you maintain consistent warmth and prolong the life of your blanket.

Berkshire EZ Touch Heated Throw Blanket Troubleshooting

If your Berkshire EZ Touch heated throw blanket feels warm but the button doesn’t light up, or if it only heats near the control button, the issue usually lies with the controller or wiring. Often, the blanket stops working on one side or only heats at the top due to internal wire breaks or faulty connections. Start by checking that the blanket lies flat and the controller is set correctly. If these steps fail, replacement is safer than repair.

A folded heated blanket beside its controller on a sofa

A common problem is the button on the controller not lighting even though the blanket produces heat. This can happen if the LED or button mechanism is faulty but the heating elements still work. The blanket heating only near the button often means the wires farther away are damaged or disconnected.

When the Berkshire EZ Touch heated throw blanket is not working on one side or only the top part heats, the internal wiring or the controller connection is likely compromised. The blanket’s internal wires run through the fabric to distribute heat evenly. Any break or short in these wires causes uneven heating.

To troubleshoot, first unplug the blanket and lay it flat on a hard surface. Check the controller settings and ensure the power cord and controller plug are securely connected. Avoid folding or bunching the blanket, which can strain internal wires.

  1. Check Controller and Power
    Confirm the controller is plugged in and the power outlet works by testing another device. Press the power button and cycle through heat settings to see if the LED lights respond.
  2. Inspect the Blanket for Damage
    Look along the blanket’s edges and seams for visible damage or fraying that could affect wiring. Do not use if you find exposed wires or burns.
  3. Straighten the Blanket Flat
    Heat elements work best when the blanket is flat. Bunching can cause uneven heat or no heat in some areas.
  4. Test Heat Distribution
    After turning the blanket on, carefully feel for warmth across the entire surface. Cold spots indicate wiring issues.
Safety Warning
Never attempt to open or repair the blanket yourself. Damaged electric blankets pose fire and shock risks. Replace the blanket if wiring is damaged or if the controller malfunctions.

If the button light remains off but the blanket heats, or if heat is uneven and localized, replacement is the best option. Repairing internal wiring is not practical or safe. New models offer updated safety features like auto shut-off and overheat protection.

For persistent problems after basic troubleshooting, consider replacing the Berkshire EZ Touch heated throw blanket. Use a UL, ETL, or CSA certified model to ensure safety. If you want help with detailed controller functions, see the section on understanding the EZ Touch controller.

What You Need
Consider these solutions for effective troubleshooting.
Easy Control
Berkshire Life Heated Throw EZ Touch
This throw features an EZ Touch button controller with 4 heat settings for straightforward temperature adjustment. Its extra-long cord and machine washable design make it practical for daily use and maintenance.
Check price on Amazon
Reversible Style
Berkshire Jacquard Faux Fur Heated Throw
This reversible heated throw offers two luxurious textures and 4 heat levels for personal comfort. It includes a 4-hour auto shut-off for safety and is machine washable after cord removal.
Check price on Amazon
More Heat Levels
Berkshire Loftmink Velvety Fleece Heated Throw
This double-sided velvety fleece throw has 5 heat settings and a built-in auto shut-off for safety. It is machine washable on gentle cycle, making it easy to keep clean and cozy.
Check price on Amazon

Steps for Troubleshooting Your Heated Throw Blanket

Start your Berkshire EZ Touch heated throw troubleshooting by checking the power source. Make sure the outlet works by plugging in another device or testing the blanket on a different outlet. A loose plug or damaged cord can cause intermittent heating or no heat at all.

  1. Check Power and Connections
    Confirm the blanket’s power cord is firmly connected to the controller and the wall outlet. Look for any visible damage or frays on the cord. Replace the cord if damaged; do not use the blanket with a compromised power supply.
  2. Inspect Controller Settings
    The controller controls heat output and safety features. Make sure it is securely plugged into the blanket. Press the power button and cycle through the heat settings to see if the indicator lights respond. If the button doesn’t light or feels stuck, the controller may be faulty.
  3. Examine the Blanket for Damage
    Lay the blanket flat on a surface and inspect for tears, holes, or areas where the heating wires might be broken. Pay special attention near the controller connection and along the seams. Physical damage can cause uneven heating or failure to warm.

Understanding the EZ Touch Controller

The EZ Touch controller has multiple heat settings that let you adjust warmth from low to high. Typically, pressing the power button cycles through three or four heat levels, each indicated by a light. The blanket heats at a consistent wattage for each setting, so choose the one that matches your comfort and energy use preferences.

  1. Select Heat Setting
    Press the power button once to turn on the blanket on the lowest heat. Each additional press increases the heat level. The indicator light changes color or number to show the current setting.
  2. Turn Off Safely
    Press and hold the power button for a few seconds to turn off the blanket. The lights should go out, confirming the controller has cut power.

Controller issues often arise from dirt, moisture, or wear on the button contacts. Keep the controller dry and clean. If the button sticks or the lights flicker, unplug the blanket and inspect the controller connection. Avoid using the blanket if the controller shows erratic behavior.

Controller Care
Store the blanket with the controller unplugged and avoid folding the cord sharply near the controller. This prevents wire fatigue and connector damage.

Maintaining Your Berkshire EZ Touch Heated Throw Blanket

Common problems with heated throw blankets include uneven heating, overheating, and failure to power on. Most issues come from dirt, damage to internal wires, or improper care. Fix these by following the cleaning and storage instructions carefully.

A cleaning brush placed next to a heated throw blanket

You can wash your Berkshire EZ Touch heated throw blanket, but only by hand or on a gentle cycle with cold water. Unplug and remove the controller before washing. Do not bleach or use fabric softeners, as these can damage the heating elements. After washing, lay the blanket flat to air dry; do not tumble dry or iron.

Avoid damaging the heating wires
Do not twist, wring, or fold the blanket sharply. This can break or short the internal wires and cause heating failure or safety hazards.
  1. Prepare for washing
    Unplug the blanket and detach the controller. Check the care label for any special instructions.
  2. Wash carefully
    Hand wash or use a gentle machine cycle with cold water and mild detergent. Avoid bleach and fabric softeners.
  3. Dry flat
    Lay the blanket flat on a clean surface to air dry. Do not use a dryer or iron.
  4. Store properly
    Roll or fold the blanket loosely without sharp creases. Store in a dry, cool place away from direct sunlight or moisture.

Proper storage prevents damage. Avoid placing heavy objects on the blanket. Ensure it’s completely dry before storing to prevent mold or mildew.

When to Replace Your Heated Throw Blanket

If your Berkshire EZ Touch heated throw stopped working despite troubleshooting, it may be time to replace it. Signs include no heat at any setting, visible damage to wires or fabric, or a controller that no longer responds.

Safety first
Do not use a blanket with exposed wires, scorch marks, or a malfunctioning controller. These pose fire and electric shock risks.

Replacement options include buying a new Berkshire EZ Touch model or choosing a different brand if you want updated features or a different size. Check for UL or ETL certification to ensure safety.

  1. Identify irreparable damage
    Look for burned areas, frayed cords, or persistent heating failures despite resets and controller replacement.
  2. Decide to replace
    If the blanket is old, damaged, or unsafe, replace it rather than risk malfunction.
  3. Choose a new blanket
    Pick one with safety features like auto shut-off and tip-over protection if you want more peace of mind.

For more options and buying advice, see our guide to the best heated throw blanket.

Frequently Asked Questions

What should I do if my Berkshire EZ Touch blanket won’t heat up?
First, check that the controller is properly connected and the power outlet works. Make sure the blanket is fully flat and not folded, as folds can prevent heating. If it still doesn’t heat, test with a different outlet or controller if possible, since a faulty controller often causes this issue.
How can I fix uneven heating in my heated throw?
Uneven heating usually comes from the blanket folding or bunching, which blocks heat distribution. Lay the blanket flat and smooth before use. If the problem continues, the internal wiring or heating elements may be damaged and require professional repair or replacement.
Is it safe to wash my Berkshire heated throw in a washing machine?
Yes, but only follow the manufacturer’s care instructions exactly. Usually, use a gentle cycle with cold water and mild detergent, and never bleach or iron the blanket. Avoid high heat drying; air dry or use a low heat setting to protect the heating elements and wiring.
What are the common issues with Berkshire heated throws?
Common problems include the controller not lighting up, heating only near the control button, uneven heat distribution, and failure to power on. These often result from controller faults, wiring damage, or improper care like folding the blanket while hot.
How can I ensure my heated blanket lasts longer?
Store the blanket flat or loosely rolled, never folded tightly. Follow washing instructions carefully to avoid damage to wiring. Disconnect the controller when not in use, and inspect cords regularly for wear or damage to prevent electrical faults.
When should I consider replacing my heated throw blanket?
Replace it if troubleshooting steps don’t restore even heating or power, if the controller or wiring is visibly damaged, or if the blanket overheats despite proper use. Safety risks increase with age and damage, so err on the side of replacement rather than repair.
Related guides

Before you buy anything, it is worth looking at ensuring blanket safety.

It helps to understand anysay heated blanket throw before spending anything.

Written by Home Heating Research Editor · United Kingdom

Daniel Mercer is the editorial persona behind HeaterSphere's home heating guides, product comparisons and practical heating advice. His work explains heating technology in plain English, examines the available evidence and makes the limitations clear.

Home heatingElectric heatersEnergy efficiencyHeating safety
More about Daniel

Keep reading